Fermentation Fridge Build

Parrots beaks, valves, condensers, and all other hardware for stilling.

Fermentation Fridge Build

Postby Yase » Sun Apr 02, 2017 11:41 pm

So after running my first ferment in the dining room, as the shed was getting way too hot, i decided to have a crack at building a ferment chamber as the smell was ok at first but after 10 days was getting a bit much for the family and it was a pain in the ass carrying the fermenters back to the shed. At first i was looking at using cool room paneling and a small bar fridge but would have cost too much money and time. I found a build on a beer forum that used a side by side fridge/freezer and after taking a few measurements to make sure it could house my 4 x 30L fermenters i went looking on trusty gumtree and found a 7 year old Maytag for $80 that had issues with maintaining temp, meaning a faulty thermistor or controller. This was perfect as i was planning on using a STC-1000 anyway.

Fridge with shelves and drawers removed (controller temporarily removed for investigation)
20170327_090202.jpg

20170327_090208.jpg


Cut plastic liner with sharp stanley knife both sides
20170327_095640.jpg


Removed foam by hand exposing the "freshness" control pipes, which were cut back
20170327_101620.jpg
You do not have the required permissions to view the files attached to this post.
Yase
 
Posts: 20
Joined: Mon Jan 25, 2016 4:02 am
Location: Perth,WA
equipment: 50L Boiler, 3600w, 2" pot still with shotgun condenser

Re: Fermentation Fridge Build

Postby Yase » Sun Apr 02, 2017 11:49 pm

Cut hole in door with a dremel for the STC-1000 and wired the supply, cool and heat circuits.
20170327_151137.jpg

20170327_151156.jpg


Bought an 80W tubular greenhouse heater off gumtree and wired in a spare 120mm PC fan i had lying around to disperse the heat. Also bolted some 50x50 aluminium angle through the side of the fridge for shelf supports to which i fixed some melamine board.
20170330_134444.jpg


Finished fermentation chamber with my second ever batch of McWhisky bubbling away happily at 29-30deg and a few extra supports for good measure :handgestures-thumbupleft:
20170331_120324.jpg


All said and done the build went really well, although there were some worrying times when cutting and drilling into the walls, and is nice to know i can ferment all year round day/night at 30 degrees :D
You do not have the required permissions to view the files attached to this post.
Yase
 
Posts: 20
Joined: Mon Jan 25, 2016 4:02 am
Location: Perth,WA
equipment: 50L Boiler, 3600w, 2" pot still with shotgun condenser

Re: Fermentation Fridge Build

Postby Fishleg » Mon Apr 03, 2017 5:43 am

Pretty Shmick mate! Good job
Fishleg
 
Posts: 307
Joined: Sun Mar 19, 2017 5:42 pm
Location: Canberra
equipment: FSD neutraliser with 85 litre keg boiler

Re: Fermentation Fridge Build

Postby Doubleuj » Mon Apr 03, 2017 6:01 am

:happy-partydance: awesome work, can I suggest eventually replacing the melamine with ply or something, if the melamine gets wet it'll fail and down comes your fermenters
Doubleuj
Lifetime Member
 
Posts: 3630
Joined: Fri Jan 16, 2015 7:15 pm
Location: rockhampton qld
equipment: 4" stainless glasser

Re: Fermentation Fridge Build

Postby copperhead road » Mon Apr 03, 2017 6:32 am

Looks sweet as mate, and you can run your still site all year round!
copperhead road
 
Posts: 777
Images: 0
Joined: Sat Mar 11, 2017 7:13 pm
Location: Brisbane Queensland
equipment: Full industrial grade copper 25 gallon short can 4" pot with 10 gallon expansion chamber and gin basket, 3" Gatlon gun condenser (gas flame)

Re: Fermentation Fridge Build

Postby Lowie » Mon Apr 03, 2017 8:27 am

:handgestures-thumbupleft:
Lowie
 
Posts: 712
Joined: Sun May 24, 2015 1:32 pm
Location: Crow eater
equipment: 4", 4 plate "Frankenfurter" copper bubbler and blockhead on a 50L 3000W electric boiler, 10000W controller - don't even know why I need that much, all grain HERMS system through 18G HLT keg and 50L mash tun.

Re: Fermentation Fridge Build

Postby bluc » Mon Apr 03, 2017 9:43 am

Great work yase :handgestures-thumbupleft: Im with doubleuj ply will be a much more reliable shelf especially if one of the fermenters puke..
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Fermentation Fridge Build

Postby Clickeral » Mon Apr 03, 2017 12:53 pm

I would personally look at dropping your fermenting temp down depending on what Yeast your using.

When I use my Fermenting fridge I sit between 10-18C depending on what I am making

Rum never gets temp controlled as the hotter the better :p
Clickeral
 
Posts: 300
Joined: Mon May 06, 2013 6:54 am
Location: Victoria
equipment: 5 Hectoliters of Fermenting space (120L temp controlled)
12 Plate modular procap bubbler with 1020mm stainless packed sections and super reflux condenser
50L Milk can boiler 2x 2400w or 70L kettle (2x 2200w)
3v nanobrewery mashing

Re: Fermentation Fridge Build

Postby Yase » Mon Apr 03, 2017 7:29 pm

Will get a sheet of marine ply to change over, thanks for the suggestion. Using the mcwhisky recipe from the forum which uses bakers yeast. From what i have read bakers yeast likes the 30 degree temp. please correct me if i'm wrong.
Yase
 
Posts: 20
Joined: Mon Jan 25, 2016 4:02 am
Location: Perth,WA
equipment: 50L Boiler, 3600w, 2" pot still with shotgun condenser

Re: Fermentation Fridge Build

Postby Kenster » Mon Apr 03, 2017 7:43 pm

yase, Noice build bud... I think the Bakers 'likes' 30 ish and will tolerate that temp quite nicely, however, the lower the temp the less congeners and off flavours are generated...& stresses the yeast less... i try for low 20s after the initial eruption.
Kenster
 
Posts: 643
Joined: Mon Aug 31, 2015 8:53 pm
equipment: Still Spirits... turbo 500...retired.(Boiler retained, added 3kw element with variable temp)
RPG...3''x1200mm LM/VM combo...400mm double wound coldie
3''x1200mm copper pot & shares leibig from combo.

Re: Fermentation Fridge Build

Postby Yase » Mon Apr 03, 2017 7:46 pm

thanks kenster, this ferment seems to have almost finished after 3 days. Ill run the next one as suggested :handgestures-thumbupleft:
Yase
 
Posts: 20
Joined: Mon Jan 25, 2016 4:02 am
Location: Perth,WA
equipment: 50L Boiler, 3600w, 2" pot still with shotgun condenser

Re: Fermentation Fridge Build

Postby Yase » Mon Apr 03, 2017 7:51 pm

Just bumped the temp down to 24 deg for the rest of the ferment. Not running till the weekend anyway.
Yase
 
Posts: 20
Joined: Mon Jan 25, 2016 4:02 am
Location: Perth,WA
equipment: 50L Boiler, 3600w, 2" pot still with shotgun condenser

Re: Fermentation Fridge Build

Postby Sam. » Mon Apr 03, 2017 8:17 pm

Kenster wrote:yase, Noice build bud... I think the Bakers 'likes' 30 ish and will tolerate that temp quite nicely, however, the lower the temp the less congeners and off flavours are generated...& stresses the yeast less... i try for low 20s after the initial eruption.


For whisky more congeners can be a benefit if you are going to age the product ;-)
Sam.
Lifetime Member
 
Posts: 10405
Joined: Sun Jul 17, 2011 7:19 pm
Location: South Oz Straya
equipment: Original FSD 5 plate 4 inch modular bubbler SSG with hand crafted plates and parrot by Mac.
18 Gal boiler.
2 x 2400W elements and power controller.
.

Re: Fermentation Fridge Build

Postby Psykamaholik » Tue Apr 04, 2017 10:33 am

Mate that looks bloody amazing! :handgestures-thumbupleft:

You've set the benchmark for my next fermentation fridge!

I have mine set to 25*C with 2*C tolerance each way
Psykamaholik
 
Posts: 199
Joined: Wed Nov 11, 2015 12:27 pm
Location: Brisneyland
equipment: Fusel express super reflux still

Re: Fermentation Fridge Build

Postby Lowie » Tue Apr 04, 2017 12:01 pm

That's a great fermenting fridge Yase. Mines pretty basic (fridge bottom, freezer top) and includes two stc controllers, one for the fridge and one for the freezer (which I us in the winter to age my beer). For those of use electrically challenged, are you able to post a diagram of your wiring as it looks pretty shmick? Cheers.
Lowie
 
Posts: 712
Joined: Sun May 24, 2015 1:32 pm
Location: Crow eater
equipment: 4", 4 plate "Frankenfurter" copper bubbler and blockhead on a 50L 3000W electric boiler, 10000W controller - don't even know why I need that much, all grain HERMS system through 18G HLT keg and 50L mash tun.

Re: Fermentation Fridge Build

Postby Yase » Tue Apr 04, 2017 9:07 pm

Not too difficult. Only mod i did on the fridge control system was disconnect the supply to the fridge damper motor, now that it's one chamber this is not required. Ran 2 x 3 core flexible cables from the STC-1000 to the back of the fridge near the compressor though the floor of the freezer area, 1 for STC-1000 supply and 1 for STC-1000 "cool". Cut the incoming fridge supply flexible cable halfway between where it enters the fridge and the "supply in" connector at the compressor area. Joined the STC-1000 power supply flex to the outgoing cut flex that has the 10A plug on it. Joined the other "cool" flex to the cut flex going to the fridge "supply in" connector. Ran a STC-1000 "heat" 3 core flex to a double power point on a mounting block at the bottom of the fridge area so i could plug in a 12V transformer for the PC fan and plug in the Greenhouse heater.

I just used standard electrical double screw "blue point" connectors for cable joining.

A few IMPORTANT notes to consider

-make sure you earth anything extra that you install that has a metal chassis.
-use caution when drilling or cutting though walls of the fridge because if you hit a gas line the fridge will be useless.
-make sure there are no sharp edges where cables pass though cut or drilled holes.


Wiring.jpg
You do not have the required permissions to view the files attached to this post.
Yase
 
Posts: 20
Joined: Mon Jan 25, 2016 4:02 am
Location: Perth,WA
equipment: 50L Boiler, 3600w, 2" pot still with shotgun condenser

Re: Fermentation Fridge Build

Postby Lowie » Wed Apr 05, 2017 8:29 am

Yase wrote:Not too difficult. Only mod i did on the fridge control system was disconnect the supply to the fridge damper motor, now that it's one chamber this is not required. Ran 2 x 3 core flexible cables from the STC-1000 to the back of the fridge near the compressor though the floor of the freezer area, 1 for STC-1000 supply and 1 for STC-1000 "cool". Cut the incoming fridge supply flexible cable halfway between where it enters the fridge and the "supply in" connector at the compressor area. Joined the STC-1000 power supply flex to the outgoing cut flex that has the 10A plug on it. Joined the other "cool" flex to the cut flex going to the fridge "supply in" connector. Ran a STC-1000 "heat" 3 core flex to a double power point on a mounting block at the bottom of the fridge area so i could plug in a 12V transformer for the PC fan and plug in the Greenhouse heater.

I just used standard electrical double screw "blue point" connectors for cable joining.

A few IMPORTANT notes to consider

-make sure you earth anything extra that you install that has a metal chassis.
-use caution when drilling or cutting though walls of the fridge because if you hit a gas line the fridge will be useless.
-make sure there are no sharp edges where cables pass though cut or drilled holes.

Cheers mate, good post.


Wiring.jpg
Lowie
 
Posts: 712
Joined: Sun May 24, 2015 1:32 pm
Location: Crow eater
equipment: 4", 4 plate "Frankenfurter" copper bubbler and blockhead on a 50L 3000W electric boiler, 10000W controller - don't even know why I need that much, all grain HERMS system through 18G HLT keg and 50L mash tun.


Return to Accessories



Who is online

Users browsing this forum: No registered users and 12 guests

x