5 Star Store
Community Guidelines
Newbies Corner
Recipes
AD searcha little different parrot
7 posts
• Page 1 of 1
a little different parrot
by Canuck » Wed Nov 27, 2013 10:16 am
this screws onto the end of my liebig.
You do not have the required permissions to view the files attached to this post.
- Canuck
- Posts: 106
- Joined: Mon Feb 25, 2013 1:19 pm
- equipment: 44" *2" VM column with double wound condenser. modular 3" VM/pot (214 cm vm,160cm pot), 50 cm 2" shot pc 4*1/2", triple wound condenser with cold finger
Re: a little different parrot
by Potmash Boka » Wed Nov 27, 2013 11:36 am
That's pretty cool Canuk. :handgestures-thumbupleft:
- Potmash Boka
- Posts: 295
- Joined: Wed Apr 17, 2013 6:18 pm
- Location: The Shire( with all the Hobbits)
- equipment: 2" pot and 4" thumper, 4" pot, 2" SS reflux, 2.5" Boka. 4" 5 plate bubbler( almost done, need to some bits and to make the column round again). SS boiler, 80L keg, 50L keg and a 30L keg boilers.
Various pieces of copper pipe laying around for future experiments.
Re: a little different parrot
by 1 2many » Wed Nov 27, 2013 2:56 pm
I think thats the nicest parrot i have seen good work. :handgestures-thumbupleft:
- 1 2many
- Lifetime Member
- Posts: 4215
- Joined: Sun Jan 27, 2013 6:08 am
- Location: Where the sun shines
- equipment: Portable A.G brewery ,#001 5 STAR blockhead 4" Modular 4 plate SSG with,6"inline thumper, 2.5" 9 tube shotgun, packed section, Boiler 50 ltr inverted keg 4"still mount, 2.4 Kw FSD elements 1"drain.
Re: a little different parrot
by dogbreath vodka » Wed Nov 27, 2013 4:05 pm
Who's a pretty boy then?
:laughing-rolling: :laughing-rolling:
Nice job Canuk, :handgestures-thumbupleft:
DBV
:laughing-rolling: :laughing-rolling:
Nice job Canuk, :handgestures-thumbupleft:
DBV
- dogbreath vodka
- Posts: 1396
- Joined: Sun Jan 15, 2012 5:10 pm
- Location: Somewhere over the rainbow
- equipment: "Steampunk 2 - 6" Bubble cap
"Jimmy" the 4" Carter head
Re: a little different parrot
by Smbjk » Wed Nov 27, 2013 4:34 pm
Great job mate. Love your work. Just make sure the little birdie doesn't drink all your booze. I know they like sweet nectar :laughing-rolling:
- Smbjk
- Posts: 863
- Joined: Fri Dec 14, 2012 11:22 pm
- Location: Brisvegas
- equipment: 50lt keg boiler with 2"boka
3" bubbler with 4 perf plates
All grain brewery ( Small Scale ) Keg Fridge
50lt keg boiler 2x2400w elements
Control box
Building fund is depleted
Re: a little different parrot
by Canuck » Thu Nov 28, 2013 12:34 am
thanks everyone! love the site, wish I was down under where its warmer. The shed is about minus 8 Celsius today!
- Canuck
- Posts: 106
- Joined: Mon Feb 25, 2013 1:19 pm
- equipment: 44" *2" VM column with double wound condenser. modular 3" VM/pot (214 cm vm,160cm pot), 50 cm 2" shot pc 4*1/2", triple wound condenser with cold finger
Re: a little different parrot
by Canuck » Thu Nov 28, 2013 3:54 am
Advice on centering ring. before I solder it, comments on this please centering ring is made from cut down 2 inch by 1 inch coupling.installing fust below the 2 by 2by one tee. Also wondering about double wound design just hangs in the top centered by the wire ring. Comments appreciated!
You do not have the required permissions to view the files attached to this post.
- Canuck
- Posts: 106
- Joined: Mon Feb 25, 2013 1:19 pm
- equipment: 44" *2" VM column with double wound condenser. modular 3" VM/pot (214 cm vm,160cm pot), 50 cm 2" shot pc 4*1/2", triple wound condenser with cold finger
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 76 guests