Blucs bubbler

Perforated & bubble cap plated columns

Re: Blucs bubbler

Postby hillzabilly » Fri Dec 29, 2017 10:03 pm

Verryy nice,as Borat would say,howd ya go at soldering the RC section up or is that were they finances have got ya by the balls with supplies,Xmas can do that pretty easy.cheers hillzabilly ;-)
hillzabilly
 
Posts: 1509
Images: 0
Joined: Sun Jun 10, 2012 3:18 pm
Location: PERTH WEST AUSSIE
equipment: 10 gallon OZARK pot still ,2inch and 3inch Nixon Stone coloum stills ,10 and 18 gal beer keg boilers,5gal thumper keg.And the one and only 4" Five Star Southern Cross .

Re: Blucs bubbler

Postby bluc » Fri Dec 29, 2017 10:10 pm

Its a bit rugged but holds town water pressure. Will post it up tomorrow after I give it a tickle. Not actually held up by cash anymore, Just gotta wait to hear from 5star for a small order couple clamps bend an end cap and few seals and can run it. Will need couple fittings from bunnings for cooling.
Also dont think 200l cooling drum will suffice will need to up the power on my radiator cooling fans to hold the heat back..
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby scythe » Sat Dec 30, 2017 8:35 am

Your on a roll now mate.
Those SSGs look good.
scythe
 
Posts: 1860
Joined: Thu Nov 14, 2013 6:34 am
Location: Central West NSW
equipment: Dreaming of a 4" bubbler

Re: Blucs bubbler

Postby bluc » Sat Dec 30, 2017 1:34 pm

Cant be bothered polishing up rc/blockhead today today to hot in the shed will get it done asap and post updated photo..

Wondering how much room between packed section and top cap is needed? I can fit 3 plates and a packed section easy as but if I have a plate on bottom and top of the top tee i could have 4 plates and a packed section.. as long as 75mm between plate and packing is enough.. or should I just stick to 3 and a packed section.. i wouldnt have a sight glass on top one then either..
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby coffe addict » Sat Dec 30, 2017 7:43 pm

Hey bud, was looking awesome earlier.

I would think 75mm would suffice as people generally run slower for neutrals and if some does splash up it won't cause problems unless it's sufficient to cause flooding.
coffe addict
 
Posts: 1027
Joined: Thu Feb 26, 2015 12:00 pm
Location: Brisbane central
equipment: 18 gal keg boiler on its side on wheel's with fill port, 1in drain and 2x2.4kw elements
4in 5 plate modular blockhead with optional infusion basket

Re: Blucs bubbler

Postby bluc » Sat Dec 30, 2017 8:18 pm

Ok sweet thanks :handgestures-thumbupleft:
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby Dig Brinker » Sat Dec 30, 2017 10:13 pm

Just go 4 plates B. No need for a packed section. I made a 600mm flanged tube for stripping and using as a packed section, haven’t used it yet. I strip over 4 plates with no reflux then spirit run over 4. Add the basket for gin.
Dig Brinker
 
Posts: 552
Joined: Sun Dec 20, 2015 5:46 am
Location: South of Melbourne
equipment: 4 inch 4 plate bubbler on keg boiler

Re: Blucs bubbler

Postby db1979 » Sat Dec 30, 2017 10:59 pm

:text-+1: I do the same.
db1979
 
Posts: 1760
Joined: Sat Dec 29, 2012 3:47 pm
Location: South of the big smoke in banana bender land.
equipment: Eve - 4" x 4 plate solid state bubbler (sieve plates), 330 mm packed section on a keg boiler with 2 x 2000 W elements.
Currently having a makeover: 2" x 4 plate solid state bubbler (1" bubble caps, no sight glasses...maybe not for much longer!) on a bain-marie boiler.

Re: Blucs bubbler

Postby db1979 » Sat Dec 30, 2017 11:06 pm

Plus stripping and combining low wines then spirit run through a 4 plate bubbler is faster than doing individual single runs through a 5 plate bubbler.
db1979
 
Posts: 1760
Joined: Sat Dec 29, 2012 3:47 pm
Location: South of the big smoke in banana bender land.
equipment: Eve - 4" x 4 plate solid state bubbler (sieve plates), 330 mm packed section on a keg boiler with 2 x 2000 W elements.
Currently having a makeover: 2" x 4 plate solid state bubbler (1" bubble caps, no sight glasses...maybe not for much longer!) on a bain-marie boiler.

Re: Blucs bubbler

Postby coffe addict » Sun Dec 31, 2017 12:45 am

Hmm, I'd wager that the neutral isn't so neutral.

I've run three times through five plates and still not been 100% happy with it!

Maybe a different wash would be easier to get to neutral but packed sections are great for stripping out flavours. My2c
coffe addict
 
Posts: 1027
Joined: Thu Feb 26, 2015 12:00 pm
Location: Brisbane central
equipment: 18 gal keg boiler on its side on wheel's with fill port, 1in drain and 2x2.4kw elements
4in 5 plate modular blockhead with optional infusion basket

Re: Blucs bubbler

Postby bluc » Thu Jan 11, 2018 2:59 pm

Baby steps but progress all the same.
Resized_20180111_144505_1508.jpeg

Gave the deflag/bkockhead a quick cleanup and some of my stuff arrived. After seiing the 5star bend I will also need a short pipe section between the blockhead and bend so the bend clears my cooling lines. I bought some more braided line and a pressure regulator. I need to track down a nipple that will go from the regulator and a standard 1/2" nipple. I bout some 15 to 10mm ones from bunnings but its smaller than that. Couple more fittings and clamps and I will be good to go :handgestures-thumbupleft:
You do not have the required permissions to view the files attached to this post.
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby hillzabilly » Thu Jan 11, 2018 3:25 pm

You could turn the 90'bend 45degrees then get a 45'bend from FSD for $19 and ya may be good,damn those little problems that shit on ya day,but there is allways a solution some were,soon very SOON grasshopper :D cheers hillzabilly ;-)
hillzabilly
 
Posts: 1509
Images: 0
Joined: Sun Jun 10, 2012 3:18 pm
Location: PERTH WEST AUSSIE
equipment: 10 gallon OZARK pot still ,2inch and 3inch Nixon Stone coloum stills ,10 and 18 gal beer keg boilers,5gal thumper keg.And the one and only 4" Five Star Southern Cross .

Re: Blucs bubbler

Postby Teddysad » Thu Jan 11, 2018 4:06 pm

coffe addict wrote:Hmm, I'd wager that the neutral isn't so neutral.

I've run three times through five plates and still not been 100% happy with it!

Maybe a different wash would be easier to get to neutral but packed sections are great for stripping out flavours. My2c

Agree. Can't beat the reflux packed column for neutrals
Teddysad
 
Posts: 443
Joined: Tue Mar 06, 2012 2:10 pm
Location: Canterbury NZ
equipment: FSD 4"SSG with packed column 50l Boiler keg. Alex 25 for smaller scale runs

Re: Blucs bubbler

Postby bluc » Thu Jan 11, 2018 4:35 pm

It would prob clear if I had the pc on an angle forward. No biggie clamps are not here yet anyhow. It will all work out :handgestures-thumbupleft:
As far as packed section I can fit 3 plates and 500mm packed so will try that.even if I have to double distill.
Instead of a fill port any problem with filling the boiler via the column? Would the full reflux part of the run clean it up ok?
On second thought prob not a good idea on grain/fruit mashs etc
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby hillzabilly » Thu Jan 11, 2018 5:06 pm

You must have a pretty low ceiling ta only fit 3plates and packed section,is that with a plate straight on the boiler or after one section ?,used ta fill one of my first boilers by pumping into the drain ,was ok for a while but got inspired by a few on this sight and had ta go with all the bells and whistles.cheers hillzabilly ;-)
hillzabilly
 
Posts: 1509
Images: 0
Joined: Sun Jun 10, 2012 3:18 pm
Location: PERTH WEST AUSSIE
equipment: 10 gallon OZARK pot still ,2inch and 3inch Nixon Stone coloum stills ,10 and 18 gal beer keg boilers,5gal thumper keg.And the one and only 4" Five Star Southern Cross .

Re: Blucs bubbler

Postby EziTasting » Thu Jan 11, 2018 5:26 pm

Hey Bluc,
looking good ... bet you can feeble the distilling going on ... :))

As for the cooling line, why not see if you can't shorten the copper and put on some elbows...?!? Our cooling lines are on a 90 degree bend...

As for a filling port, I'd agree with Hillz, not having a dedicated fill port is a royal PITA!
We've got a 2' and if I'd be given a second chance I would go 3" - just be so much easier!

Who was it, just recently posted a pic of a boiler with a 90 degree bend on the side as a fill port and Temp gauge ... ?!? forget now... - but that would almost be the way to go IMO.
EziTasting
 
Posts: 2084
Joined: Fri Sep 25, 2015 5:15 pm
Location: FNWA
equipment: Newbie - Keg Boiler & 4" 4 plate glasser

Re: Blucs bubbler

Postby Doubleuj » Thu Jan 11, 2018 5:30 pm

It was DB who had the fill port out the side
Doubleuj
Lifetime Member
 
Posts: 3630
Joined: Fri Jan 16, 2015 7:15 pm
Location: rockhampton qld
equipment: 4" stainless glasser

Re: Blucs bubbler

Postby bluc » Thu Jan 11, 2018 6:23 pm

Have thought about soldering elbows etc but I think I like the spacer idea better.. desicions..
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby bluc » Thu Jan 11, 2018 6:39 pm

My bottom plate sits on a "spacer" tri clamp pipe
Hilzabilly.. until I can afford a decent boiler with a 4"ferrule.
I have a 1/2" female bsp to 1.5" tri clamp coming for fill port but is on the slow boat from you know where.. looking at an interim solution..

Going to move my thermoport is at bottom currently, gunna move that to middle for more accurate reading and going to put another bulkhead directly above the old thermometer hole and link it up with silicone hose for a sight glass meter. And the fillport up top..
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: Blucs bubbler

Postby EziTasting » Thu Jan 11, 2018 7:23 pm

bluc wrote:...until I can afford a decent boiler with a 4"ferrule.


Again, just my opinion - get a 6” ferrule on the boiler!!! Easier to get your arm into it when needed!
I can’t get past my forearms on a 4” and I’m not big/phat or have a Tradie’s forearms...
EziTasting
 
Posts: 2084
Joined: Fri Sep 25, 2015 5:15 pm
Location: FNWA
equipment: Newbie - Keg Boiler & 4" 4 plate glasser

PreviousNext

Return to Plated Column Stills



Who is online

Users browsing this forum: No registered users and 19 guests

x