Re: Rum Glass
Posted: Mon Apr 25, 2016 2:05 pmdrinka wrote:Awesome work there rummy! Any chance you could post a pic of how you use the dynabolt to expand the 1/2"?
:handgestures-thumbupleft:
:handgestures-thumbupleft:
Page 9 of 9
Posted: Mon Apr 25, 2016 2:05 pm:handgestures-thumbupleft:
Re: Rum Glass
Posted: Sat Aug 13, 2016 8:12 pmSo I finally measured a collection rate with 4 plates with a thumper.
Note due to the sugar head ag wash being very temperamental because of it foaming and bubling I have had to back it off a little.
How 100mls a minute sound :dance:
Note due to the sugar head ag wash being very temperamental because of it foaming and bubling I have had to back it off a little.
How 100mls a minute sound :dance:
Re: Rum Glass
Posted: Sat Aug 13, 2016 8:34 pmYou gotta to be happy with that collection rate mate.
Cheers,
Prof. Green
Cheers,
Prof. Green
Re: Rum Glass
Posted: Sat Aug 13, 2016 9:15 pmrumdidlydum wrote:So I finally measured a collection rate with 4 plates with a thumper.
Note due to the sugar head ag wash being very temperamental because of it foaming and bubling I have had to back it off a little.
How 100mls a minute sound :dance:
Note this collection rate isint taking into acount the time stoping and going into full rflux to refill the thumper
Re: Rum Glass
Posted: Sat Aug 13, 2016 10:28 pmThat's a thumping thumper, tried for dancing bananas but they didn't work, so you'll have to be happy with : :happy-partydance: :clap:
Re: Rum Glass
Posted: Sat Aug 13, 2016 11:04 pm:handgestures-thumbupleft:
That's a little quicker than I push but like me I bet your wishing for a bigger boiler to keep it feed now :laughing-rolling:
That's a little quicker than I push but like me I bet your wishing for a bigger boiler to keep it feed now :laughing-rolling:
Re: Zak's Heart of Gold
Posted: Mon Aug 15, 2016 11:29 pmrummy, was the problem with the cooling from the 1mm or so wall on the inner tubes and the larger end plate was too thick?
if so maybe brazing 20+ on thinner end plate might be ok?
if so maybe brazing 20+ on thinner end plate might be ok?
Re: Rum Glass
Posted: Tue Aug 16, 2016 7:10 amIt was an absolute disaster trying to use the thick plate.
I cut them off and made normal end caps, they were the ones that developed leaks.
I cut them off and made normal end caps, they were the ones that developed leaks.
Re: Rum Glass
Posted: Fri Oct 14, 2016 8:17 pmUpdate on the illuminated chicken leg boiler...
The led setup has slowly died over the last few runs. I'm fairly confident in saying the heat destroyed them prematurely.
I have made up a mark two the other day and trying it out now. A fair bit different the height, vent holes easily dismantled so that I can replace the leds if they fail.
I expect this version to last a bit longer than the previous setup.
Cheers
The led setup has slowly died over the last few runs. I'm fairly confident in saying the heat destroyed them prematurely.
I have made up a mark two the other day and trying it out now. A fair bit different the height, vent holes easily dismantled so that I can replace the leds if they fail.
I expect this version to last a bit longer than the previous setup.
Cheers
Re: Rum Glass
Posted: Sun Oct 16, 2016 7:50 pmLoving the build, this is a beast of a still.
Re: Rum Glass
Posted: Tue Sep 19, 2017 1:33 pmWonder has anyone taken this one step further and lit up the tees? Hows is the re design holding up.. :-B