boiler drain plumbing

Boiler, burner and boiler modification talk.

boiler drain plumbing

Postby stretch69 » Wed Oct 22, 2014 7:30 am

Hi guys,

As it is I have a 3/4" ss skin fitting with a 3/4" ss tap attached directly to that. Its not very practical because it makes the boiler way higher than it needs to be.

My plan is to get some legs with castors welded on shortly so I need change the way its plumbed up.

I want to go from the skin fitting to a 90° elbow then a pipe about 7 to 8" long that I could put the tap on. This way the tap will be kinda horizontal now.

where can I buy a 3/4" x 8" ss nipple fitting?
Or can I just use some kind of water pipe?
Thanks
stretch69
 
Posts: 293
Joined: Wed Sep 04, 2013 7:38 pm
Location: Adelaide - Northern Suburb's
equipment: 4" 4 plate FSD Bubbler!
50l Boiler

Re: boiler drain plumbing

Postby thegoose » Wed Oct 22, 2014 7:41 am

Hi Stretch
Mate mine set up the way you want yours I welded some nipples to SS pipe you could easily use the threaded brass extensions that you can buy at Bunnings to extend the tap out. Also I have my boiler on a dolly just a piece of form ply with castors screwed to the bottom you can adjust the height to clear the tap cheap and easy :handgestures-thumbupleft:
thegoose
 
Posts: 63
Joined: Thu Oct 17, 2013 10:04 pm
Location: Sunshine Coast, Queensland
equipment: Retired 2" boka
3" modular bubbler

Re: boiler drain plumbing

Postby huggy_b » Wed Oct 22, 2014 8:42 am

I'm not sure how your boiler is set up, but we had ours upside down and utilised the 2" bung to attach our drain.
Our boiler sits fairly high, but it was designed that way to get a 20L bucket under it for emptying.

From our build thread:

RS_Gav wrote:Boiler drain tap made up with from a FSD 2" blank welded to a a 90deg.

Image


Boiler legs welded in place onto a keg we purchased half complete

Image
Image


huggy_b
 
Posts: 127
Joined: Wed Jan 01, 2014 10:54 am
Location: Perth, Wait Awhile
equipment: 4" glasser (5 plates)

Re: boiler drain plumbing

Postby halfbaked » Wed Oct 22, 2014 9:16 am

REAL NICE!
halfbaked
 
Posts: 69
Joined: Mon Jan 14, 2013 10:17 am
equipment: still lookin

Re: boiler drain plumbing

Postby stretch69 » Wed Oct 22, 2014 9:28 am

Thanks goose, I didn't think of welding nipples to some pipe :handgestures-thumbupleft:

Huggy, I drain mine with a hose attached to the tap to the garden. I kinda want the tap to be sitting just outside the rim of the keg if you know what I mean. The boiler will be less than 10" off the ground so I kind of don't really want the tap underneath.
stretch69
 
Posts: 293
Joined: Wed Sep 04, 2013 7:38 pm
Location: Adelaide - Northern Suburb's
equipment: 4" 4 plate FSD Bubbler!
50l Boiler

Re: boiler drain plumbing

Postby woodduck » Wed Oct 22, 2014 3:50 pm

This is what i did if it helps.

I did the same, i just cut and welded fittings.
You do not have the required permissions to view the files attached to this post.
woodduck
Lifetime Member
 
Posts: 3497
Joined: Mon Jun 16, 2014 5:54 pm
Location: Good old country SA
equipment: 4 plate 6" copper bubbler, 6 plate 4" glass bubbler with 500mm packed section three way thumper sitting on a 50 ltr keg boiler with 6000watts, 2" pot still and a 2" boka.

Re: boiler drain plumbing

Postby MacStill » Wed Oct 22, 2014 3:56 pm

I have keg envy 8-}
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: boiler drain plumbing

Postby stretch69 » Wed Oct 22, 2014 8:48 pm

Woodduck, that's pretty much what I'm trying to achieve but with fittings ideally because my mate that can tig weld is working interstate at the moment
stretch69
 
Posts: 293
Joined: Wed Sep 04, 2013 7:38 pm
Location: Adelaide - Northern Suburb's
equipment: 4" 4 plate FSD Bubbler!
50l Boiler

Re: boiler drain plumbing

Postby woodduck » Wed Oct 22, 2014 9:06 pm

You could buy the elbow with threads then poke the male thread through a hole in the bottom of the keg and use a part of a female fitting cut short to use as a nut,would only need to be 5 or so mm long, then use a ss washer and a silicon baking sheet as a seal. Only problem will be that the fitting may stick up a bit and not be flush with the bottom so it won't drain completely. Did any of that make sense? Following? I can do a picture if you need? I have seen short bits of ss pipe with threads on each end that can extend out to your tap or if your really stuck i have seen all thread pipe but only in brass but you might be able to get it in ss.

This may be ok for a temporary fix untill your mate gets back then he can just weld the fitting into your keg.

Hope this helped.

Good luck :handgestures-thumbupleft:
woodduck
Lifetime Member
 
Posts: 3497
Joined: Mon Jun 16, 2014 5:54 pm
Location: Good old country SA
equipment: 4 plate 6" copper bubbler, 6 plate 4" glass bubbler with 500mm packed section three way thumper sitting on a 50 ltr keg boiler with 6000watts, 2" pot still and a 2" boka.

Re: boiler drain plumbing

Postby stretch69 » Thu Oct 23, 2014 7:59 am

Thanks woodduck,
This is the fitting I already have in there.
I'll be able to get a 3/4" elbow easy, it's just the bit that goes to the tap.
I might for the time being just get some threaded brass pipe like you said. I'll try to either get the ss nipple or I'd prob be happy even with 3/4" ss threaded pipe like you said.
Thanks for the tips :handgestures-thumbupleft:
You do not have the required permissions to view the files attached to this post.
stretch69
 
Posts: 293
Joined: Wed Sep 04, 2013 7:38 pm
Location: Adelaide - Northern Suburb's
equipment: 4" 4 plate FSD Bubbler!
50l Boiler

Re: boiler drain plumbing

Postby Meatheadinc » Thu Oct 23, 2014 2:03 pm

having a tap underneath and not protruding is great when on castors as there is nothing to catch when moving.

threads are level wit the outside edge for easy access and a hose is attached to drain ( the beauty of split level house)

boilertap.jpg


I have had a drain that protruded and was forever catching when I moved it around.
You do not have the required permissions to view the files attached to this post.
Meatheadinc
 
Posts: 561
Joined: Thu Aug 29, 2013 9:00 pm
Location: Far North Coast NSW
equipment: 2" LM/VM on 30L boiler
4" FSD Neutraliser 50L boiler
4" carter head thump column
"Control Freak"- Semi Automation

Re: boiler drain plumbing

Postby Whiskyaugogo » Thu Oct 23, 2014 2:32 pm

Some wooden bling :handgestures-thumbupleft:
Whiskyaugogo
Site Donor
 
Posts: 649
Joined: Mon Jun 16, 2014 2:48 pm
Location: Canberra, Australia
equipment: To be updated

Re: boiler drain plumbing

Postby stretch69 » Thu Oct 23, 2014 5:14 pm

That is some serious wooden bling!
Is that stainless pipe underneath?
stretch69
 
Posts: 293
Joined: Wed Sep 04, 2013 7:38 pm
Location: Adelaide - Northern Suburb's
equipment: 4" 4 plate FSD Bubbler!
50l Boiler

Re: boiler drain plumbing

Postby MacStill » Thu Oct 23, 2014 6:08 pm

stretch69 wrote:That is some serious wooden bling!


:text-imwithstupid:

Seriously impressive boiler shroud, the best I've seen yet :handgestures-thumbupleft:
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: boiler drain plumbing

Postby Meatheadinc » Thu Oct 23, 2014 6:15 pm

thank guys
yep stainless keg and stainless pipe. the woods just a heat shield and some bling can see more in my welcome thread viewtopic.php?f=3&t=6973
Meatheadinc
 
Posts: 561
Joined: Thu Aug 29, 2013 9:00 pm
Location: Far North Coast NSW
equipment: 2" LM/VM on 30L boiler
4" FSD Neutraliser 50L boiler
4" carter head thump column
"Control Freak"- Semi Automation

Re: boiler drain plumbing

Postby Heef71 » Sat Oct 03, 2015 2:27 pm

Bottom drain 2.sm..jpg
I had seen some designs with a nipple on the side of the keg for a drain point, but you cant completely drain the whole thing. A fellow distiller has the same problem with a bought milk can boiler.
I cut off the 2" flange where the spear goes, flipped my keg upside down, and welded on a 2' to 3/4' right angle reducer, screwed in a 150mm length of 3/4" s/s pipe, attached a 3/4" ball valve and a 3/4" right angle to direct the flow down.
My keg also sits on 4 x 3" casters to aid mobility and to raise it off floor level. It works great.
When doing neutrals the boiler is on the floor, when doing rums the boiler sits on a wooden box if made up so I can get a bucket underneath to collect the dunder.
You do not have the required permissions to view the files attached to this post.
Heef71
 
Posts: 57
Joined: Sat Mar 29, 2014 6:08 pm
Location: N.T.
equipment: 4" 5 plate glass modular bubbler with packed section on a keg with 2 x 2400W elements & power controller. Started with a T500 and made some mod's and added a 2nd lid with a copper pot head.


Return to Boilers & burners.



Who is online

Users browsing this forum: No registered users and 8 guests

x