A section for all electrical discussions, including controllers, elements, wiring diagrams & schematics.
Forum rules
By participating in this section you acknowledge you are aware of aussiedistiller,com.au forum rules, policies & disclaimer.
If you are not aware please go to the rules section "before" you continue in this area of our forums.
"you expressly agree to hold aussiedistiller.com.au, Administration and moderator team, harmless for any property damage, personal injury and/or death, or any other loss or damage that may result from your use of the information or service provided here in and through out our forums"
the information found in our forums, are from many sources, qualified and un qualified as is the nature of the internet, and as such you use this information at your own risk. No liability directly or indirectly will be accepted by aussiedistillers.com.au, administration, the mod team or their heirs, whatsoever.
Regards,
aussiedistiller team.
by Lowey79 » Fri Jan 19, 2018 11:34 am
Hey guys, I’m hoping to get some advice from those with experience...
I’m getting organized to build a new pot still for my T500 boiler, and I want to set up a controller while I’m at it.
I’ve read up on PID and Voltage type controllers, but I haven’t seen any direct comparisons. Does one type work better than the other? And what are the pros and cons for either type.
Cheers for any advice offered!
-
Lowey79
-
- Posts: 12
- Joined: Sat Oct 28, 2017 5:50 pm
- Location: Latrobe Valley, Victoria.
- equipment: T500 for the time being... Looking to build a replacement in the near future
by Doubleuj » Fri Jan 19, 2018 11:38 am
You’ll want a voltage controller.
From what I know about it is that a VC allows for infinite control over power, allowing you to slow down or speed up the boiling of your wash. Therefore controlling your output speed
A PID is more for setting a desired temp and keeping that temp constant, like when mashing all grain
-
Doubleuj
- Lifetime Member
-
- Posts: 3630
- Joined: Fri Jan 16, 2015 7:15 pm
- Location: rockhampton qld
- equipment: 4" stainless glasser
by Maximus_Moonshine » Tue Aug 07, 2018 2:12 am
How did you go with this? Did it live up to expectations?
Cheers
Chris
-
Maximus_Moonshine
-
- Posts: 27
- Joined: Fri Aug 03, 2018 1:11 pm
- Location: Near Beechworth, Victoria
- equipment: Turbo 500 reflux and alembic pot
by baznkez » Tue Aug 07, 2018 10:37 am
Hi Mate this is the one i use i built a box for it saftey 1st !!!! i use it on my t500 boiler when i use the pot still head
4000W 220V SCR Speed Controller Motor Electronic Variable Voltage Regulator Fan
volt.jpg
You do not have the required permissions to view the files attached to this post.
-
baznkez
-
- Posts: 38
- Joined: Wed Mar 29, 2017 5:08 pm
- Location: Brisbane QLD best place on earth
- equipment: turbo 500 & alembic pot with controller
by Chris7231 » Mon Sep 03, 2018 4:11 pm
Maximus_Moonshine wrote:How did you go with this? Did it live up to expectations?
Cheers
Chris
It's going fine (touch wood)
It's great to know exactly what voltages to dial in...
You do not have the required permissions to view the files attached to this post.
-
Chris7231
-
- Posts: 23
- Joined: Sun May 20, 2018 10:25 am
- equipment: Still Spirits reflux & alembic setups.
by Rakija » Fri Oct 05, 2018 5:46 pm
Hi Chris 7231 ,
Thanks for posting the link for the voltage controller and the picture of your control box that you made.
It look great, that’s exactly what I want to make. I bought the same controller from the link.
Could you PLEASE Scribble down a scetch of how you wired the parts together?
Also I see a fuse in the box too. How many amps did you make the circut?
Thanks mate
-
Rakija
-
- Posts: 2
- Joined: Wed Oct 03, 2018 1:25 pm
- equipment: Turbo 500
by j0sh2008 » Fri Oct 05, 2018 6:03 pm
If your asking for sketch of the wiring diagram, you should really get a sparky to wire it up mate. These things are simple to make but if your asking questions like that get a sparky. You don’t want to kill yourself or someone else :law-policered:
-
j0sh2008
-
- Posts: 231
- Joined: Mon Dec 05, 2016 1:07 am
- Location: Brisbane
- equipment: 4" 5star still - 4 plates + 500mm packed section
100L milk can boiler - 2400W & 3600W FSD elements.
2 X 1000L IBC - Recirculating water
by Rakija » Fri Oct 05, 2018 7:51 pm
I know how to wire the box but I have never wired /used a digital display like that before that’s why I asked for a sketch.
-
Rakija
-
- Posts: 2
- Joined: Wed Oct 03, 2018 1:25 pm
- equipment: Turbo 500
by Chris7231 » Wed Oct 10, 2018 10:37 am
Rakija wrote:I know how to wire the box but I have never wired /used a digital display like that before that’s why I asked for a sketch.
You just connect the LCD wires to the same connections as your output connections that go to your boiler.
-
Chris7231
-
- Posts: 23
- Joined: Sun May 20, 2018 10:25 am
- equipment: Still Spirits reflux & alembic setups.
Return to Electrical Hardware
Who is online
Users browsing this forum: No registered users and 49 guests