Electrical Controller Problem

A section for all electrical discussions, including controllers, elements, wiring diagrams & schematics.
Forum rules
By participating in this section you acknowledge you are aware of aussiedistiller,com.au forum rules, policies & disclaimer.
If you are not aware please go to the rules section "before" you continue in this area of our forums.

"you expressly agree to hold aussiedistiller.com.au, Administration and moderator team, harmless for any property damage, personal injury and/or death, or any other loss or damage that may result from your use of the information or service provided here in and through out our forums"

the information found in our forums, are from many sources, qualified and un qualified as is the nature of the internet, and as such you use this information at your own risk. No liability directly or indirectly will be accepted by aussiedistillers.com.au, administration, the mod team or their heirs, whatsoever.

Regards,

aussiedistiller team.

Electrical Controller Problem

Postby Walker » Sat Mar 07, 2020 5:21 am

A question about electricity. I built a controller, 240 volt, 40 amp SSVR with a manual dial potentiometer, I installed a digital watt, amp, voltage meter just to see what was going on. I have a 5000 watt heating element. I went to test it, in water bucket, and the voltage is correct in and out to the heating element. However it’s only showing a 190 watt draw with a .60 amp draw approximately. Not sure what this means is the SSVR bad? Is the heating element bad? Any ideas as to what’s wrong. The heating element was used. Thanks
Walker
 
Posts: 19
Joined: Wed Mar 04, 2020 2:05 am
equipment: Nothing yet!

Re: Electrical Controller Problem

Postby Doubleuj » Sat Mar 07, 2020 6:21 am

Hey mate, firstly, are you a sparky? If not, tut tut tut and get a sparky to check it out.
Doubleuj
Lifetime Member
 
Posts: 3630
Joined: Fri Jan 16, 2015 7:15 pm
Location: rockhampton qld
equipment: 4" stainless glasser

Re: Electrical Controller Problem

Postby Walker » Sat Mar 07, 2020 6:42 am

Nope no sparky here but this isn’t rocket science stuff. If I can build the controller, which I did, following instructions posted here and other places then I shouldn’t need a sparky. Can’t get a professional for every problem I come across. Treat electricity with respect and you will have no problems. My problem seems simple and was looking for some advice. If I don’t get any I’ll still figure it out myself. No offense I know you mean well!
Walker
 
Posts: 19
Joined: Wed Mar 04, 2020 2:05 am
equipment: Nothing yet!

Re: Electrical Controller Problem

Postby Tesla101 » Sat Mar 07, 2020 7:59 am

The furst and easiest thing to do would be to test the element. Take a resistance reading and then use Ohms law and the info you already have to determine if the element is OK or not.

If it's OK then the controller is shot. Up to you if you want to try and trouble shoot it or you can get a new 4800w controller from 5 star for 43 bucks plus shipping. They also have a great range of elements
Tesla101
 
Posts: 327
Joined: Thu Jan 09, 2020 6:48 pm
equipment: ......

Re: Electrical Controller Problem

Postby Andrew » Sat Mar 07, 2020 8:25 am

Sorry but a 5000w element would kill our controllers
Edit to add: a “normal” home has 10amp outlets suitable for 2400w elements.
Some homes may have 15amp that is suited to 3600w elements
I have no idea what would be needed to run a 5000w element
Maybe that’s the first place to start ???
Last edited by Andrew on Sat Mar 07, 2020 8:28 am, edited 1 time in total.
Andrew
 
Posts: 393
Images: 0
Joined: Sat Jun 11, 2011 12:58 pm
Location: S.E.Brisbane
equipment: Anything I choose From The 5 Star Range

Re: Electrical Controller Problem

Postby Professor Green » Sat Mar 07, 2020 9:11 am

Hi Walker, I would advise that you have a sparky check this out to make sure it is both wired correctly and safely.

Also a 5000 Watt element requires 20 amps, where are you running this from?
Professor Green
 
Posts: 2483
Joined: Fri Apr 17, 2015 1:10 pm
Location: Victoria
equipment: FSD 100 litre milk can with 2 x 2400W elements
FSD Neutraliser
FSD Carter Head
12 litre double boiler with 2400W element

Re: Electrical Controller Problem

Postby Walker » Sat Mar 07, 2020 9:59 am

Thanks everyone but I got it all sorted out. In the US the normal household current 120 volts, 15 amps, second would be 120 volts, 20 amps for higher draw appliances. My controller is none of these it’s 30 amp, 240 volts, 10 gauge copper wire. Kind of normal stuff here. Well anyway the problem was a faulty heating element. I’ll change that and be all set. Thanks
Walker
 
Posts: 19
Joined: Wed Mar 04, 2020 2:05 am
equipment: Nothing yet!

Re: Electrical Controller Problem

Postby The Stig » Sat Mar 07, 2020 10:21 am

That info of NOT being in AU would have been handy in the first post.
Glad you got it sorted
The Stig
Site Nerd
 
Posts: 18192
Images: 9
Joined: Sun Jun 19, 2011 8:37 am
equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy

Re: Electrical Controller Problem

Postby Walker » Sat Mar 07, 2020 10:24 am

Ya I kinda figured that out after a fashion I’ll be more careful with that.
Walker
 
Posts: 19
Joined: Wed Mar 04, 2020 2:05 am
equipment: Nothing yet!

Re: Electrical Controller Problem

Postby Tesla101 » Sat Mar 07, 2020 8:31 pm

:think:

Walker wrote:Thanks everyone but I got it all sorted out. In the US the normal household current 120 volts, 15 amps, second would be 120 volts, 20 amps for higher draw appliances. My controller is none of these it’s 30 amp, 240 volts, 10 gauge copper wire. Kind of normal stuff here. Well anyway the problem was a faulty heating element. I’ll change that and be all set. Thanks


Sorry walker but that doesn't make sense. If your mains voltage is 120v how are you running a 240v controller?
If you say the higher appliances are120v 20A then that's 2400 Watts.

How can you run a 5000w element?
Tesla101
 
Posts: 327
Joined: Thu Jan 09, 2020 6:48 pm
equipment: ......

Re: Electrical Controller Problem

Postby Walker » Sat Mar 07, 2020 11:45 pm

Tesla101 sorry I didn’t explain in detail enough. In my area the common or by code required main entrance power to a home is 200 amps. This power runs to a main circuit panel where it is then used to wire 120 or 240 volt items. Wiring in the home uses 14 gauge wire for 15 amp receptacles such has lighting, tv, stereo etc., lower wattage. For heavier loads 12 gauge wire for 20 amp receptacles is used for things like refrigerators, toasters, microwave ovens etc., higher wattage. All these use 120 volts of power. 240 volts can run through 12 gauge wire to a certain amperage also.

240 volts is require for items such as electric stoves, hot water heaters, cloths driers, welders etc. you would wire accordingly for the device being used. Wire size would determine increased wattage limits. Most items would use 8 gauge or larger wire. All this is well documented.

For my controller I have or had a 5000 watt heating element. This element requires a 30 amp, 240 volt, hook up in the main panel box and requires minimum 10 gauge wire. This system does limit where the controller can be used.

Also US uses 60 hertz and most other countries 50 hertz. Inventor Nikola Tesla.

Electricity is pretty tricky stuff but simple if you are educated properly. It’s easily a handyman project for anyone with a little mechanical knowledge, controller.
Walker
 
Posts: 19
Joined: Wed Mar 04, 2020 2:05 am
equipment: Nothing yet!

Re: Electrical Controller Problem

Postby Tesla101 » Sun Mar 08, 2020 8:56 am

Walker wrote:
Electricity is pretty tricky stuff but simple if you are educated properly. It’s easily a handyman project for anyone with a little mechanical knowledge, controller.


It may be a handyman project, however I would still get a licensed electrician to do any mains powered work.

Remember, if there does happen do be an electrical fault somewhere that causes your house to burn down, the first thing the insurance company is going to want to know is who installed the device that caused the electrical fault. If it was not a licensed electrician, then I'm afraid you're on your own.
Tesla101
 
Posts: 327
Joined: Thu Jan 09, 2020 6:48 pm
equipment: ......

Re: Electrical Controller Problem

Postby The Stig » Sun Mar 08, 2020 10:08 am

Let’s not get carried away Tesla
We don’t know what happens in the good old US of A compared to Australia.
The Stig
Site Nerd
 
Posts: 18192
Images: 9
Joined: Sun Jun 19, 2011 8:37 am
equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy

Re: Electrical Controller Problem

Postby Tesla101 » Sun Mar 08, 2020 5:00 pm

Yep no worries Stig.

Sorry Walker if I came across as a bit of a smart ass. Sounds like you know what you're doing.

To get 240v mains in the US is it 3 phase or still just single phase?
Tesla101
 
Posts: 327
Joined: Thu Jan 09, 2020 6:48 pm
equipment: ......

Re: Electrical Controller Problem

Postby Tesla101 » Sun Mar 08, 2020 5:29 pm

Hi Walker,

Re Ohm's Law to determine if your element was faulty or not...

To test if your element had failed you could've measured the resistance and then used Ohm's law to calculate if it was faulty or not. If it's a 5000w 240v element, then using the P=V*I formula the current you'd expect to flow would be 5000=240*I, 5000/240 = 20.83amps. Then by using Ohm's law V=I*R to calculate the resistance you would transpose that to R = V/I. So 240/20.83 would give you 11.52 ohms for your element.

Sorry if it came across as a joke, was just trying to help out.
Tesla101
 
Posts: 327
Joined: Thu Jan 09, 2020 6:48 pm
equipment: ......

Re: Electrical Controller Problem

Postby Walker » Mon Mar 09, 2020 1:24 am

Thanks Tesla101 I just used a multimeter much simpler.
Walker
 
Posts: 19
Joined: Wed Mar 04, 2020 2:05 am
equipment: Nothing yet!

Re: Electrical Controller Problem

Postby FilthyPhil » Fri Mar 12, 2021 4:08 pm

Hi, I know you get what you pay for & I'm regretting buying this cheap Chinese controller but there weren't any other options at the time.
2 of the wires have come loose probably due to crappy soldering & I'm not sure where they go. If someone could point me in the right direction so I can re- solder them please.
You do not have the required permissions to view the files attached to this post.
FilthyPhil
 
Posts: 64
Joined: Sun Sep 06, 2020 9:29 pm
Location: Newcastle
equipment: I have built a 50l keg boiler with 2 x 2400w elements & a 2" copper pot still with shotgun condenser.

Re: Electrical Controller Problem

Postby FilthyPhil » Fri Mar 12, 2021 4:15 pm

Sorry, I'm having dramas trying to get the 2nd pic to show up.
FilthyPhil
 
Posts: 64
Joined: Sun Sep 06, 2020 9:29 pm
Location: Newcastle
equipment: I have built a 50l keg boiler with 2 x 2400w elements & a 2" copper pot still with shotgun condenser.

Re: Electrical Controller Problem

Postby The Stig » Fri Mar 12, 2021 5:27 pm

Try a new message or what error do you get ?
Last edited by The Stig on Fri Mar 12, 2021 5:28 pm, edited 1 time in total.
The Stig
Site Nerd
 
Posts: 18192
Images: 9
Joined: Sun Jun 19, 2011 8:37 am
equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy

Re: Electrical Controller Problem

Postby bluc » Fri Mar 12, 2021 7:41 pm

FilthyPhil wrote:Hi, I know you get what you pay for & I'm regretting buying this cheap Chinese controller but there weren't any other options at the time.
2 of the wires have come loose probably due to crappy soldering & I'm not sure where they go. If someone could point me in the right direction so I can re- solder them please.

Nothing should be soldered on 240v :angry-banghead:
bluc
Site Donor
 
Posts: 8967
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Next

Return to Electrical Hardware



Who is online

Users browsing this forum: No registered users and 2 guests

cron

x