How to.... easy, easy flange.

Posts in this forum should be a complete method, educational, with pics where applicable,posts made in this area that don't fit this criteria will be moved at mods discretion.

How to.... easy, easy flange.

Postby MacStill » Sat Mar 26, 2011 3:37 pm

Ok here's how I do my version of an easy flange, there are other ways but this is the most simple and effective I've ever made.

Part 1.

Step 1.
Wrap a length of 1/4 inch tube around a piece of 2inch pipe, do a few wraps and keep the tension on with your hands until you end up with a coil.
Then put the coil in a vise and cut a slot through the lot with a hacksaw.... gently does it.

Once you end up with a few rings, hard solder them to form a solid ring.

4 start rings.jpg


5 ring on.jpg


Step 2.
With the end of the pipe you want to flange, bell the end slightly on an anvil or on your vice, gently at first and about 6mm flared out. once the end is at about 45 degrees you can now flatten it to 90 degrees with short sharp taps, again just gentle, it will form but dont rush and theres no need to anneal the pipe first.

1 begin bend.jpg


2 bend done.jpg


3 bend flat.jpg


Step 3.
Place the ring over the pipe you intend to use for your column to keg join, flatten ring with short sharp taps with a hammer.

5 1 ring on pipe.jpg


6 ring flat.jpg


Cont.
You do not have the required permissions to view the files attached to this post.
Last edited by Sam. on Tue Aug 15, 2017 8:15 pm, edited 1 time in total.
Reason: Inserted new pics due to photobucket fiasco - cheers Woodduck
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby MacStill » Sat Mar 26, 2011 3:44 pm

Step 3a.

What you end up with should look like this.

7 ready to solder.jpg


Step 4.

Solder the ring to column after you get it all plumbed up and clean up the joint with a chainsaw file.

8 heat and solder.jpg


9 done.jpg


Step 5.

Check for fit to keg and clamp. You might need to do up and undo the clamp a couple of times to get it all to bed in nicely.

10 clamped.jpg


Cont.
You do not have the required permissions to view the files attached to this post.
Last edited by Sam. on Tue Aug 15, 2017 8:17 pm, edited 1 time in total.
Reason: Inserted new pics due to photobucket fiasco - cheers Woodduck
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby MacStill » Sat Mar 26, 2011 3:51 pm

All done

11 holding up.jpg


You can also use these to make a sight glass.


Cheers.
You do not have the required permissions to view the files attached to this post.
Last edited by Sam. on Tue Aug 15, 2017 8:18 pm, edited 1 time in total.
Reason: Inserted new pics due to photobucket fiasco - cheers Woodduck
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby SBB » Sat Mar 26, 2011 4:27 pm

Interesting post McStill...thanks.
SBB
SBB
Lifetime Member
 
Posts: 2451
Joined: Mon Mar 21, 2011 8:12 pm
Location: Northern NSW
equipment: (The Pelican) a 2 inch pot / stripper on 25L electric boiler interchangable with T500 reflux still...... 2 1/2 inch pot still on 50L keg (gas burner).....
3 inch Boka (half share with Draino),...... 4 inch 4 plate perforated plate Bubbler

Re: How to.... easy, easy flange.

Postby TJM » Sun Jun 19, 2011 1:05 am

Hey this is great. Would this flange work ok with a sightglass and tri clamp?
TJM
 
Posts: 40
Joined: Sun Jun 12, 2011 10:44 am

Re: How to.... easy, easy flange.

Postby MacStill » Sun Jun 19, 2011 7:44 am

TJM wrote:Hey this is great. Would this flange work ok with a sightglass and tri clamp?


Sure does ;)

..... and remember you first seen it here :mrgreen
Last edited by MacStill on Sun Jun 19, 2011 9:39 am, edited 1 time in total.
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby MacStill » Sun Jun 19, 2011 8:20 am

in the link I provided used as a sight glass 5Star :roll: :roll: :roll:
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby R-sole » Sun Jun 19, 2011 9:31 am

Your link don't work Captain :? :lol: :lol:
R-sole
 
Posts: 0
Joined: Mon Apr 18, 2011 4:15 am
Location: Northern NSW Australia
equipment: Keg based pot stiller. 3" vm for occasionally making product for macerations and redistillation.

Re: How to.... easy, easy flange.

Postby MacStill » Sun Jun 19, 2011 9:41 am

Does now :lol: :oops: :oops:

Gotta fix the way links show up, dont like the way it's formatted at the moment
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby tipsy » Sun Jun 19, 2011 11:26 am

McStill wrote:With the end of the pipe you want to flange, bell the end slightly on an anvil or on your vice, gently at first and about 6mm flared out. once the end is at about 45 degrees you can now flatten it to 90 degrees with short sharp taps, again just gentle, it will form but dont rush and theres no need to anneal the pipe first.


Hi McStill, I've had my 2" copper sitting around for ages (probably over 12 months)
Should I anneal it?
tipsy
 
Posts: 863
Joined: Mon Jun 06, 2011 1:34 pm
Location: South Gippsland, VIC.
equipment: 4" Mac 4 with packed section and gin basket on a 50lt boiler with 2 2400w FSD elements.

Re: How to.... easy, easy flange.

Postby MacStill » Sun Aug 28, 2011 7:44 am

tipsy wrote:
McStill wrote:With the end of the pipe you want to flange, bell the end slightly on an anvil or on your vice, gently at first and about 6mm flared out. once the end is at about 45 degrees you can now flatten it to 90 degrees with short sharp taps, again just gentle, it will form but dont rush and theres no need to anneal the pipe first.


Hi McStill, I've had my 2" copper sitting around for ages (probably over 12 months)
Should I anneal it?


See Step 2. above mate ;)
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby crozdog » Mon Aug 29, 2011 12:07 pm

I just fount this thread - thanks just what I was looking for. I have a roll of 1/4' annealed i can use to make a bunch for my next build.

McStill, i'm curious about 2 things :
1. Am I right that this works for 4" too? or is the 4" flange a bit bigger?
2. how long does it take you to make one these in 2" & 4"?

I'm not l looking forward to the cost of buying 15 x 2' & 5 x 4" flanges... so hope it works for 4' too

cheers
crozdog
 
Posts: 132
Joined: Fri Jul 29, 2011 11:23 am
equipment: 2" Bok
2" VM
2" pot
50l modified laundry copper for a boiler

Re: How to.... easy, easy flange.

Postby MacStill » Mon Aug 29, 2011 12:24 pm

1. Am I right that this works for 4" too? or is the 4" flange a bit bigger?
2. how long does it take you to make one these in 2" & 4"?


It works fine on 4"

Only takes about 10 minutes max to make one in 4" and a little less for 2"

Making an easy flange also negates the need to solder/braze Stainless to copper.

;)
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby SBB » Mon Aug 29, 2011 12:32 pm

Croz they really are easy to make.....Im usually hopeless at forming metal into shapes.
I had my first 2 inch one made in about 25 min and it worked perfectly.
SBB
Lifetime Member
 
Posts: 2451
Joined: Mon Mar 21, 2011 8:12 pm
Location: Northern NSW
equipment: (The Pelican) a 2 inch pot / stripper on 25L electric boiler interchangable with T500 reflux still...... 2 1/2 inch pot still on 50L keg (gas burner).....
3 inch Boka (half share with Draino),...... 4 inch 4 plate perforated plate Bubbler

Re: How to.... easy, easy flange.

Postby MacStill » Mon Aug 29, 2011 12:36 pm

You can also skip step 2. if it's for a non structural joint, or if you use brazing rods on a structural joint.

Makes it even quicker and easier :mrgreen:
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby crozdog » Mon Aug 29, 2011 12:38 pm

McStill & SBB - thanks for the quick replies.

will give em a go!
crozdog
 
Posts: 132
Joined: Fri Jul 29, 2011 11:23 am
equipment: 2" Bok
2" VM
2" pot
50l modified laundry copper for a boiler

Re: How to.... easy, easy flange.

Postby stimson » Tue Sep 20, 2011 8:41 pm

brilliant idea.... :clap:
:text-thankyoublue:
stimson
 
Posts: 13
Joined: Mon Sep 19, 2011 8:48 pm
Location: SE QLD
equipment: 2" bokabob
2" pot still
3" flute
4" flute
25L boiler
50L boiler

Re: How to.... easy, easy flange.

Postby Skeeter » Sat Jan 14, 2012 8:46 am

Hey guys. Did these pics get messed up with the holiday fiasco? Or Something else? Either way think we can get them reposted? This seems to be exactly what I have been searching for, for weeks....
Skeeter
 
Posts: 1
Joined: Wed Jan 11, 2012 2:30 pm
equipment: None yet

Re: How to.... easy, easy flange.

Postby MacStill » Sat Jan 14, 2012 9:02 am

Will repost this arvo :handgestures-thumbupleft:
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: How to.... easy, easy flange.

Postby dogbreath vodka » Sat Apr 07, 2012 4:34 pm

Just made my first easy easy flange in about .... 15 minutes start to finish... damn easy :D :D
Paint me " happy" :D :D


McStill wrote:
"Snip"

You can also use these to make a sight glass.

Image

Cheers.


What do you use for the outer section of the sightglass to fit between the glass and the triclamp?
And what kind of cork is that?

Have been putting off making a flute because of the cost and the sight glass issues.
But with your method for them the cost will be low and the finish will be great.


DBV
dogbreath vodka
 
Posts: 1396
Joined: Sun Jan 15, 2012 5:10 pm
Location: Somewhere over the rainbow
equipment: "Steampunk 2 - 6" Bubble cap
"Jimmy" the 4" Carter head

Next

Return to Tips From The Workbench



Who is online

Users browsing this forum: No registered users and 2 guests

x