Commercial brew tin

Discussions about beer and wine making.

Re: Commercial brew tin

Postby Listo » Sun Aug 01, 2021 6:20 pm

RuddyCrazy wrote:Well that second batch I did using the Dutch lager is reminiscent of the reason I gaveup making homebrew beer :angry-banghead: where my first batch was full clingy goodness this batch is no head and flat as a tack. Now I did put the same amount of priming sugar in with both batchs so where it went wrong has got me beat. Now shaking the bottles does show some activity and as prior learning goes open the stubbies outside after shaking :laughing-rolling: :laughing-rolling: :laughing-rolling: this batch didn't even fizz up one bit. So there are going in a few box's to forget about for 6 months and when I get a chance I'll do a reat of batch one.


It might not be all lost, you could try soda stream? Our apprentice at work has been experimenting with it, because it has a little bit of precarbination it will take a little bit of experimentation to see what works, but with no secondary fermentation at all, soda stream sounds like it works pretty good.
Listo
 
Posts: 130
Joined: Sat Mar 15, 2014 12:45 pm
Location: Sarina Qld
equipment: 5Star 4” Modular Pot Still

Re: Commercial brew tin

Postby Listo » Fri Aug 13, 2021 2:22 pm

I got off call yesterday and was half clubbed up all day thinking of getting home and tasting my NZ pale ale to see how the hops experiment went. Looked nice and golden and had a thick creamy head (that doesn’t mean a lot to me, but does for others).
First sip was fairly strong, a little too much like an IPA I thought. By half a schooner, it was down the sink and it took a can and a half of goat to get the bitterness off the back of my tongue. I now have 46l of fertiliser. I believe the hops experiment was a failure :sad:
I’ll have to buy a 30 pack on my way home now
Listo
 
Posts: 130
Joined: Sat Mar 15, 2014 12:45 pm
Location: Sarina Qld
equipment: 5Star 4” Modular Pot Still

Re: Commercial brew tin

Postby RuddyCrazy » Sun Aug 22, 2021 1:52 pm

Had a couple of stubbies of this Dutch Lager now it has aged a bit and the first one did taste pretty nice with the stubbie staying clingy but the second one wasn't the same and no matter of shaking the stubbie would leave a head.

So this batch is going down for 6 months atleast and when I get a chance I'll do another batch of that first lager brew I did. I don't think this is a ride off and it just needs time to mature.

Now the difference between the first and second brew I did with the first I bottled it pronto after it finished fermenting where with the second one I left it for a month. So that may be the cause of the slow maturation rate of this batch and lesson learnt to bottle the brew as soon as 3 readings show the same. I did try bulk priming with my apple cider runs but I went back to priming each bottle with the beer as the cider bottles were close to exploding bombs when opened.

A few years ago I read a PDF off a lager forum where it is said by putting a re-hydrated yeast in at the end of fermentation will aid in the second fermentation in the bottle so I tried that with the cider and found out it did work out too well :laughing-rolling: :laughing-rolling: :laughing-rolling:

Cheers Bryan
RuddyCrazy
Mentor
 
Posts: 1917
Joined: Thu Oct 31, 2013 6:36 pm
Location: Not far from Kanmantoo SA
equipment: 4" copper bubbler with a setup for Neutral and a thumper for Whisky and my old 5 litre pot for doing maceration runs and MiniMe the baby pot still also a 1-1/2" pot still and bubbler build happening

Re: Commercial brew tin

Postby Wellsy » Sun Aug 22, 2021 5:01 pm

KABOOMMMM!!!!!!
There is supposed to be an earth shattering KABOOM
Wellsy
Site Donor
 
Posts: 1397
Joined: Sat Aug 22, 2020 7:48 am
Location: Victoria
equipment: FSD 4” Modular Pot Still plus 4 FSD Bubble plates on FSD 50 ltr Milk Can Boiler + 2 x 2400W FSD Element and Guard Kits

Previous

Return to Beer & Wine



Who is online

Users browsing this forum: No registered users and 3 guests

x