A section for all electrical discussions, including controllers, elements, wiring diagrams & schematics.
Forum rules
By participating in this section you acknowledge you are aware of aussiedistiller,com.au forum rules, policies & disclaimer.
If you are not aware please go to the rules section "before" you continue in this area of our forums.
"you expressly agree to hold aussiedistiller.com.au, Administration and moderator team, harmless for any property damage, personal injury and/or death, or any other loss or damage that may result from your use of the information or service provided here in and through out our forums"
the information found in our forums, are from many sources, qualified and un qualified as is the nature of the internet, and as such you use this information at your own risk. No liability directly or indirectly will be accepted by aussiedistillers.com.au, administration, the mod team or their heirs, whatsoever.
Regards,
aussiedistiller team.
by Ned » Tue Sep 04, 2018 7:19 pm
Has anyone used one of these.
I wonder if they would do the job ?
AC 220V 10000W SCR Electronic Voltage Regulator Temperature Speed Adjust Controller Dimming Dimmer Thermostat
From www.5stardistilling.com.au
You do not have the required permissions to view the files attached to this post.
-
Ned
-
- Posts: 184
- Joined: Fri Sep 29, 2017 8:13 am
- equipment: 4" 4 Plate Bubbler with 500m packed section/blockhead and 50 litre milk can. Only the best.
by The Stig » Tue Sep 04, 2018 7:33 pm
Link ?
-
The Stig
- Site Nerd
-
- Posts: 18232
- Images: 9
- Joined: Sun Jun 19, 2011 8:37 am
- equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy
by Ned » Tue Sep 04, 2018 8:08 pm
Last edited by
Ned on Tue Sep 04, 2018 8:09 pm, edited 1 time in total.
-
Ned
-
- Posts: 184
- Joined: Fri Sep 29, 2017 8:13 am
- equipment: 4" 4 Plate Bubbler with 500m packed section/blockhead and 50 litre milk can. Only the best.
by db1979 » Tue Sep 04, 2018 8:21 pm
I've been using one of these, also from www.5stardistilling.com.au. Bought two cause they were so cheap but the first one is still going strong.
https://m.www.5stardistilling.com.au.com/item/32348503806.html10000 W is more than enough for 2400 W element, but better to be safe than sorry, especially if the quality may not be the best.
-
db1979
-
- Posts: 1760
- Joined: Sat Dec 29, 2012 3:47 pm
- Location: South of the big smoke in banana bender land.
- equipment: Eve - 4" x 4 plate solid state bubbler (sieve plates), 330 mm packed section on a keg boiler with 2 x 2000 W elements.
Currently having a makeover: 2" x 4 plate solid state bubbler (1" bubble caps, no sight glasses...maybe not for much longer!) on a bain-marie boiler.
by The Dark Alchemist » Tue Oct 02, 2018 5:18 pm
Ned wrote:Has anyone used one of these.
I wonder if they would do the job ?
AC 220V 10000W SCR Electronic Voltage Regulator Temperature Speed Adjust Controller Dimming Dimmer Thermostat
From www.5stardistilling.com.au
Ned,
I ordered one and it arrived last week; wired it up last night and will be giving it a try out tomorrow night...
-
The Dark Alchemist
-
- Posts: 113
- Joined: Tue Aug 14, 2018 12:10 pm
- Location: Vic
- equipment: FSD 200L Milk Can
FSD 4" Pot Still
FSD Neutraliser
Copper T-500
by PeterC » Fri Oct 05, 2018 5:18 pm
I have something similar and was not happy with how well the AU plug fits into the multi-plug socket. Another post on this forum recommended to use a UK to AU adaptor for these types of socket and that is an excellent suggestion. Much better contact.
-
PeterC
-
- Posts: 221
- Joined: Sun Feb 05, 2017 12:20 am
- Location: Perth WA
- equipment: An 18gall. (80L) keg boiler. A 50L Keg boiler. A 4 plate, 4 inch glass column, 500mm packed section Carter head. A 1.8L all copper micro still for small batches of Gin. Plus other bits.
by The Dark Alchemist » Fri Oct 05, 2018 9:24 pm
PeterC wrote:I have something similar and was not happy with how well the AU plug fits into the multi-plug socket. Another post on this forum recommended to use a UK to AU adaptor for these types of socket and that is an excellent suggestion. Much better contact.
Snug as a bug for me, no issues..... used it 2 nights ago. 50% dribble; 100% flow. All good.
-
The Dark Alchemist
-
- Posts: 113
- Joined: Tue Aug 14, 2018 12:10 pm
- Location: Vic
- equipment: FSD 200L Milk Can
FSD 4" Pot Still
FSD Neutraliser
Copper T-500
by mako » Sun Nov 04, 2018 4:11 am
I have 2 like this -
https://www.ebay.com.au/i/264004437108?chn=psBought 2 just in case I wrecked one. Works just beautifully.
Amazing what's available in electronics these days, and so cheap :)
-
mako
-
- Posts: 16
- Joined: Fri Aug 17, 2018 12:39 pm
- equipment: Beer brewer moving to stills as well.
by ANTONY » Wed Jun 30, 2021 2:07 pm
[Hi All .
Just bought a 5 Star ,4000 watt 10 amp and 2400Wheating element to hook into my SS beer keg for boiler .
Any one out there who can give me any ideas as to hooking it all up? I was advised to get a Sparky to do the wiring .
Any pictures will be great . Any advise also .
Im new to this game as I went from my Kentucky Pot dinosaur (see pictures) to a Nixon stone reflux (see picture).
Cheers .
Antony
You do not have the required permissions to view the files attached to this post.
-
ANTONY
-
- Posts: 38
- Joined: Sun Jul 30, 2017 9:32 am
- Location: CYGNET TASMANIA
- equipment: Home made copper Kentucky Still with thumper
Nixon Stone reflux still
by chipboy » Wed Jun 30, 2021 5:31 pm
You will need a 1 inch stainless nipple cut in half and welded reasonably low to screw it into, then get it wired by someone licenced. not hard or difficult but good when done right.
-
chipboy
-
- Posts: 246
- Joined: Sun Apr 05, 2020 3:56 pm
- equipment: 50 litre keg, insulated and 4 plates at 4 inch. Home made mash tun.
by ANTONY » Thu Jul 01, 2021 8:47 am
Hi Chip
Thanks for the reply
Got the nipple .getting it welded this week end . Hard part is the Sparky to wire it. spoken to a coupla and both said it was ''beyond'' their capability ??
Cant be that difficult but I guess their house wire'ers.I will keep trying.
Onwards
-
ANTONY
-
- Posts: 38
- Joined: Sun Jul 30, 2017 9:32 am
- Location: CYGNET TASMANIA
- equipment: Home made copper Kentucky Still with thumper
Nixon Stone reflux still
by BigRig » Thu Jul 01, 2021 9:35 am
I think they are pulling your leg. They should be able to wire an element. I posted the job on hipages. Got a response within mins. Sparky was out the next day and done with 30 mins.
Fyi, I posted "need 2 heating elements (home brew set up) wired to a lead & plug".
The controller from Andrew is plug and play.
-
BigRig
-
- Posts: 757
- Joined: Sun Apr 07, 2019 1:29 pm
- Location: Brisbane, QLD
- equipment: FSD 4" Mac SSG, 50L Milk Can, 2 x 2400w elements, 35L Digiboil Boiler, Airstill.
by iOnaBender » Thu Jul 01, 2021 10:02 am
Hi Antony,
Buy some 1.5mm2 3 core flexible cable, a Clipsal 3 pin plug top. Follow instructions on the underside of the cardboard. I suggest soldering the connection or using one of these from Jaycar [/url]https://www.jaycar.com.au/3-wire-porcelain-terminal-block-30-amp/p/HM3185[/url]. If you go the solder option make sure you put a small sleeve of heat shrink on each wire BEFORE soldering together :angry-banghead:
Put a lug straight on the earth cable, don't fit it off into the porcelain block, make sure your earth wire is longer that the combined length of the brown/blue in flexible cable and the element tails. This way if it happens to get pulled out of the gland the earth wire is the last wire to be broken
Cheers
Last edited by
iOnaBender on Thu Jul 01, 2021 10:07 am, edited 1 time in total.
-
iOnaBender
- Site Donor
-
- Posts: 258
- Joined: Sat May 08, 2021 11:33 am
- Location: D'Aguilar Qld
- equipment: FSD 4" Mac 5 SSG
125ltr NANO Pro boiler
FSD 2" Pot Still
75ltr Insulated Mash Tun
95ltr HLT
by ANTONY » Thu Jul 01, 2021 1:24 pm
Thank you onabender and big rig for the quick reply's
as u said they must be pulling my leg . I will be taking it over to Mr Sparky around beer o clock and Im sure he can put a plug on the beast.
And also thanks for the schematics which i will show the man too .
I will keep you informed as my Old Copper Boiler is springing leaks and sinking fas ast as the Titanic .
After roughly 80 years + 5 years of Destilling such is life .
Cant wait to get away from Gas /open flame
Again Cheers
Antony
-
ANTONY
-
- Posts: 38
- Joined: Sun Jul 30, 2017 9:32 am
- Location: CYGNET TASMANIA
- equipment: Home made copper Kentucky Still with thumper
Nixon Stone reflux still
by The Stig » Thu Jul 01, 2021 1:55 pm
Any competent sparky should be able to do the job in 10 mins .
-
The Stig
- Site Nerd
-
- Posts: 18232
- Images: 9
- Joined: Sun Jun 19, 2011 8:37 am
- equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy
by iOnaBender » Thu Jul 01, 2021 7:28 pm
It took me 11 minutes...........are you saying I'm not competent? :teasing-tease: :laughing-rolling: :laughing-rolling:
And oh so sexual with the CABAC metal plated glands!
![Image](https://i.imgur.com/XLNfaoY.jpg)
Cheers
-
iOnaBender
- Site Donor
-
- Posts: 258
- Joined: Sat May 08, 2021 11:33 am
- Location: D'Aguilar Qld
- equipment: FSD 4" Mac 5 SSG
125ltr NANO Pro boiler
FSD 2" Pot Still
75ltr Insulated Mash Tun
95ltr HLT
by The Stig » Thu Jul 01, 2021 7:45 pm
:teasing-neener:
-
The Stig
- Site Nerd
-
- Posts: 18232
- Images: 9
- Joined: Sun Jun 19, 2011 8:37 am
- equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy
by Lowie » Fri Jul 02, 2021 8:49 pm
Did I read correctly that you are running 4000W on a 10 amp plug? That is downright dangerous and you will melt your plug and most likely fuse your power board if you don't have a safety switch. 2400W is the maximum you can and should run on a 10 amp circuit. Danger Will Robinson...
-
Lowie
-
- Posts: 712
- Joined: Sun May 24, 2015 1:32 pm
- Location: Crow eater
- equipment: 4", 4 plate "Frankenfurter" copper bubbler and blockhead on a 50L 3000W electric boiler, 10000W controller - don't even know why I need that much, all grain HERMS system through 18G HLT keg and 50L mash tun.
by The Stig » Fri Jul 02, 2021 9:27 pm
Settle petal,
He’s running a, or will be running a 2400w element through one of FSD’s 10amp power controllers that have a 15amp cut out etc etc I won’t go into what these controllers can or can’t handle but we all know they are rated to 10amp
-
The Stig
- Site Nerd
-
- Posts: 18232
- Images: 9
- Joined: Sun Jun 19, 2011 8:37 am
- equipment: Only the Best will Do.
Mac4 SSG Bubbles of Joy
by Lowie » Fri Jul 02, 2021 11:18 pm
He wrote a 4000W and a 2400W. what's it going to be? Yes, 2400W is ok on a 10A circuit. 4000W not ok!
-
Lowie
-
- Posts: 712
- Joined: Sun May 24, 2015 1:32 pm
- Location: Crow eater
- equipment: 4", 4 plate "Frankenfurter" copper bubbler and blockhead on a 50L 3000W electric boiler, 10000W controller - don't even know why I need that much, all grain HERMS system through 18G HLT keg and 50L mash tun.
Return to Electrical Hardware
Who is online
Users browsing this forum: No registered users and 64 guests