First go at building pot still

Pot still design and discussion

First go at building pot still

Postby doogie » Thu Sep 03, 2020 4:46 pm

OK, going to bite the bullet and attempt to make my own pot still to go on my T500 boiler. Here's my plan;

Still plan.PNG

The purpose for the join in the column is so I can pack it with botanicals for gin which is what I'll be mainly distilling.

Comments feedback appreciated.
You do not have the required permissions to view the files attached to this post.
doogie
 
Posts: 29
Joined: Fri Aug 07, 2020 6:43 pm
Location: Melbourne
equipment: T500 with stainless steel condenser

Re: First go at building pot still

Postby doogie » Thu Sep 03, 2020 6:06 pm

Well first hurdle, apparently 50mm copper pipe doesn't fit inside a 50mm to 20mm reducer 8-}
doogie
 
Posts: 29
Joined: Fri Aug 07, 2020 6:43 pm
Location: Melbourne
equipment: T500 with stainless steel condenser

Re: First go at building pot still

Postby bluc » Thu Sep 03, 2020 7:01 pm

Or a 50mm ferrule. You need a straight coupler to joing to anything :angry-banghead:

There are codes on fittings some same size some expsnded. Unfortunately i am to cut to remember 8-}
Last edited by bluc on Thu Sep 03, 2020 7:03 pm, edited 1 time in total.
bluc
 
Posts: 7650
Joined: Tue Apr 14, 2015 5:47 pm
Location: sunshine coast
equipment: 2" pot with 2" shotty 400mm long 5x 1/2" on a t500 boiler.
50l keg boiler 4" still mount 4" sight glass 1" drain..
4 plate 4" bubbler, 600mm packed section

Re: First go at building pot still

Postby doogie » Thu Sep 03, 2020 7:22 pm

Thanks bluc, I should have known not to assume :o
doogie
 
Posts: 29
Joined: Fri Aug 07, 2020 6:43 pm
Location: Melbourne
equipment: T500 with stainless steel condenser

Re: First go at building pot still

Postby RC Al » Thu Sep 03, 2020 8:15 pm

Ok so ifn you dont have access to an expander, as bluc said, they make these wonderful things called couplers/sockets
These are even local to you
https://plumbingsales.com.au/copper-tub ... ckets.html

with the 15mm on your plan do you mean dn15 15.88mm or 1/2" 12.7mm ?
Either way the 25mm jacket is a bit big, also get the liebig connectors as close to the ends of the jackets as possible
Last edited by RC Al on Thu Sep 03, 2020 8:18 pm, edited 1 time in total.
RC Al
Mentor
 
Posts: 1051
Joined: Mon Oct 23, 2017 4:58 pm
Location: Sunshine Coast Area
equipment: Old SS Reflux
2" Potty on 50l keg Uber burner

Re: First go at building pot still

Postby doogie » Thu Sep 03, 2020 9:01 pm

Thanks Al, I’ll go down to a 20mm jacket then. As for the 50mm yes I know about couplers, as I said wrongly assumed a 50mm to 20mm reducer would connect a 50mm pipe to a 20mm pipe. It’s a bit hard in Melbourne at moment not being able to physically visit the stores.
doogie
 
Posts: 29
Joined: Fri Aug 07, 2020 6:43 pm
Location: Melbourne
equipment: T500 with stainless steel condenser

Re: First go at building pot still

Postby dans.brew » Thu Sep 03, 2020 9:30 pm

Looks good doogie. A simple pot opens up your options with what you can make. :handgestures-thumbupleft:
Is your 15mm to 20mm reducer going to be soldered or a union fitting? A union will allow you to move the condenser angle rather than it being fixed and also remove it for cleaning.
Just a thought... id imagine you'd have to be very careful putting botanicals in a 50mm column.. wouldn't want to cause a blockage. I'm not saying dont do it but just be careful not to jam too much in it. :handgestures-thumbupleft:
Last edited by dans.brew on Thu Sep 03, 2020 9:31 pm, edited 1 time in total.
dans.brew
 
Posts: 948
Joined: Fri Oct 07, 2016 10:26 pm
Location: Victoria- Northern Wimmera
equipment: Pure Distilling Reflux Still
2" Pot Still with lieberg
4" x 4 plates Bubbler with 2"bubble caps on 50ltr keg boiler

Re: First go at building pot still

Postby doogie » Fri Sep 04, 2020 4:42 pm

dans.brew wrote:Looks good doogie. A simple pot opens up your options with what you can make. :handgestures-thumbupleft:
Is your 15mm to 20mm reducer going to be soldered or a union fitting? A union will allow you to move the condenser angle rather than it being fixed and also remove it for cleaning.
Just a thought... id imagine you'd have to be very careful putting botanicals in a 50mm column.. wouldn't want to cause a blockage. I'm not saying dont do it but just be careful not to jam too much in it. :handgestures-thumbupleft:

Hi Dan
The 20mm - 15mm is going to be a push on connection so I can easily remove. On further reflection will probably put the botanicals in the boiler and put bits of orange or grapefruit in the column.

doogie
doogie
 
Posts: 29
Joined: Fri Aug 07, 2020 6:43 pm
Location: Melbourne
equipment: T500 with stainless steel condenser

Re: First go at building pot still

Postby Lesgold » Fri Sep 04, 2020 9:04 pm

Hi dogie,

That design should work but I’d be looking at a longer condenser to keep your spirit cooler. On a slow gin run it would do the job but would not handle a stripping run without a lot of cool water being thrown at it. Good luck with the build.

Cheers

Les
Lesgold
 
Posts: 348
Joined: Thu Sep 19, 2019 2:42 pm
Location: NSW south coast
equipment: Pure Distilling reflux and pot. 2” modular CCVM/ 1150mm column, 50l boiler with 2x 2400w elements.

Re: First go at building pot still

Postby doogie » Sat Sep 05, 2020 12:56 am

Lesgold wrote:Hi dogie,

That design should work but I’d be looking at a longer condenser to keep your spirit cooler. On a slow gin run it would do the job but would not handle a stripping run without a lot of cool water being thrown at it. Good luck with the build.

Cheers

Les

Thanks Les, what length would you recommend? I do have a T500 condenser that I’m using to make neutral at the moment.
doogie
 
Posts: 29
Joined: Fri Aug 07, 2020 6:43 pm
Location: Melbourne
equipment: T500 with stainless steel condenser

Re: First go at building pot still

Postby Lesgold » Sat Sep 05, 2020 6:35 pm

I’ve recently completed two builds and put shotgun condensers on both of them. Your boiler element would be around 2000w so it won’t need too much to keep product cool. I would still build a 2” shotty to enable you to run it flat out on stripping runs. The disadvantage is that it does take a little more time to make than a Liebig.
Lesgold
 
Posts: 348
Joined: Thu Sep 19, 2019 2:42 pm
Location: NSW south coast
equipment: Pure Distilling reflux and pot. 2” modular CCVM/ 1150mm column, 50l boiler with 2x 2400w elements.


Return to Pot Stills



Who is online

Users browsing this forum: No registered users and 10 guests

x