condenser coils

Reflux still design and discussion

condenser coils

Postby Kimbo » Sat Apr 02, 2011 9:38 pm

Hi Guys,
1. has any of you built a cold finger? if so how does it compare to a standard coil?
2. is there any advantage to installing a sight glass to a Boka?
3. does any one know how to make/ where to buy a sight glass?
4. do any of you insulate your columns and boilers?
i'm always interested to hear new ideas, and why you do the things that suit you.
Kimbo
Lifetime Member
 
Posts: 5461
Images: 0
Joined: Fri Mar 18, 2011 6:33 pm
Location: Perf WA
equipment: 4" bubbler with a 6"inline thumper

Re: condenser coils

Postby MacStill » Sat Apr 02, 2011 9:47 pm

kimbo wrote:Hi Guys,
1. has any of you built a cold finger? if so how does it compare to a standard coil?
2. is there any advantage to installing a sight glass to a Boka?
3. does any one know how to make/ where to buy a sight glass?
4. do any of you insulate your columns and boilers?
i'm always interested to hear new ideas, and why you do the things that suit you.


1 cold fingers work ok, not as efficient as a double helix coil though. but they do work quite well.

2 not really, just adds "wow factor"

3 I make them, buying is fucken hopeless..... if you need some let me know, I'm making some now for my kryptonite flute and could end up with enough for a spare.

4 Yes for a 3" bok your going to need to insulate the column, yes I have a shroud around my boiler too (see boiler in show your still topic)

advise.... double wound helix coil condenser, fuck the sight glass, insulate ;)
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P

Re: condenser coils

Postby Kimbo » Sat Apr 02, 2011 9:51 pm

Thanks mate,
a wealth of knowledge as always :D
Kimbo
Lifetime Member
 
Posts: 5461
Images: 0
Joined: Fri Mar 18, 2011 6:33 pm
Location: Perf WA
equipment: 4" bubbler with a 6"inline thumper

Re: condenser coils

Postby maheel » Mon Apr 04, 2011 11:02 am

i insulate my keg boiler with an old wool blanket when in use, it speeds up heat up and would assist in stability.

my boka has about 60cm of insulation from the plates down
but has around a 30cm gap between the keg and the insulation i need a longer piece.
it is just car roll bar looking foam (commercial refirge foam tube insulation )

insulation IMO "must" help with stability in regards to breeze and changes in outside air temps etc
again IMO stability is good but i am sure opinions differ which is also good :)
maheel
 

Re: condenser coils

Postby bundy » Mon Apr 04, 2011 11:30 am

Clark rubber have meter lengths of insulation, like foam stubby coolers, you have to split to fit around column, then zip tie.
bundy
 
Posts: 141
Joined: Sat Mar 19, 2011 7:54 am
Location: Nth.Qld.
equipment: Double reducer reflux still
pot still
both on 25lt electric boiler

Re: condenser coils

Postby reknaw » Mon Apr 04, 2011 1:16 pm

I have been meaning to Insulate mine for ages but just have'nt gotten around to it, might have to get off my arse and do something.
reknaw
 
Posts: 829
Joined: Sun Mar 20, 2011 3:53 pm

Re: condenser coils

Postby Kimbo » Mon Apr 04, 2011 6:49 pm

Sounds good, i have a roll of Aircell (silver padded Insulation) at work and a roll of 100mph tape.
i think that should do the trick :D
Kimbo
Lifetime Member
 
Posts: 5461
Images: 0
Joined: Fri Mar 18, 2011 6:33 pm
Location: Perf WA
equipment: 4" bubbler with a 6"inline thumper

Re: condenser coils

Postby MacStill » Mon Apr 04, 2011 10:21 pm

Most of those cheap store like the $2 shops sell those blue camping mats that roll up, these make great insulation for a reflux column ;)
MacStill
Lifetime Member
 
Posts: 16835
Joined: Fri Mar 18, 2011 1:40 pm
Location: Wide Bay QLD
equipment: Anything I choose :P


Return to Reflux Stills



Who is online

Users browsing this forum: No registered users and 9 guests

x